Cinderella Ironing Cover: Sizing and Fit Buying Guide

Quick answer

The Cinderella Ironing Cover is a spare part made for the Cinderella Table, so the right size is the one that matches that table rather than a measurement you take from a generic board. Before ordering, confirm you own the Cinderella Table and that you iron with a steam iron, because the cover is steam-ironing proof. If you are shopping for a standard ironing board, this cover is not the correct replacement.

Why this cover is a compatibility purchase, not a size purchase

Most replacement ironing covers are sold by length and width, which is why the usual advice is to measure your board and match the numbers. The Cinderella Ironing Cover works differently: it is listed as a spare part designed for the Cinderella Table, so fit is determined by the table model you already own, not by a tape measure alone. That single fact changes the buying process. You are not hunting for the closest match in a range of sizes; you are confirming that your furniture is the piece this cover was made for.

This is also why a generic ironing board cover fit guide will not help you here. Those guides assume a flat board with a tapered nose and a drawstring or elastic edge. The Cinderella cover is tied to a specific table, so the useful check is your existing furniture and how you use it, not the dimensions of a board you might buy later.

How to measure your ironing board when a cover is sold by size

If you are also replacing a cover on a conventional board elsewhere in the home, the standard method still applies. Measure the length from tip to tip, then the width at the widest point, and note whether the board has a tapered or squared-off end. Covers are usually sized to a range, so a board measuring within a stated range will normally fit, while a board at the very top of a range may pull tight at the nose.

Measure the board itself rather than the old cover. Covers stretch with heat and use, so a worn cover can read several centimetres longer than the board underneath it. If your board has a fitted pad, measure with the pad in place, since the cover sits over it. These steps apply to standard boards; they do not determine whether the Cinderella Ironing Cover fits, because that cover is matched to the Cinderella Table.

What the steam-ironing proof claim actually covers

The Cinderella Ironing Cover is described as steam-ironing proof, which means it is suitable for use with a steam iron. That matters because steam is the usual failure point for covers: repeated moisture and heat can break down a surface that was only built for dry pressing. If you iron with a steam iron, this is the specification to look for, and it is the main functional reason to choose this cover over a generic one.

It does not tell you the cover is indestructible or that any iron setting is fine. The supplied information says steam-ironing proof and nothing more, so treat heat settings, iron plate condition, and how long you rest a hot iron in one spot as normal good practice rather than something the cover is guaranteed to absorb.

Colour and condition: the two details buyers overlook

The cover is available in Ironing Cover Off White, and colour is the option type offered. Off white is a practical choice for an ironing surface because it lets you see what you are pressing and does not transfer dye the way a dark cover can. It also shows scorch marks and staining sooner, which is useful as an early warning that your iron temperature is too high or the cover needs cleaning.

Condition is the other detail. Because this is a spare part, it is meant to restore a table that is already in use rather than to convert something else into an ironing station. If your existing cover has developed a shiny patch, a scorched spot, or a surface that has stopped gripping fabric, replacing it is the sensible move. If the table itself is damaged, a new cover will not correct that.

Decision rules for buying the Cinderella Ironing Cover

• You own the Cinderella Table: This cover is listed as a spare part for that table, so ownership is the fit test. Check the table before you check any measurement. If yes, this is the correct replacement cover.
• You use a steam iron: The cover is steam-ironing proof, which is the specification that separates it from a cover built only for dry pressing. If you press with steam, this cover matches how you work.
• You are covering a standard ironing board: A standard board needs a cover sized to its length and width, not a table-specific spare part. Measure tip to tip and across the widest point, with any pad in place. If you have a standard board, buy a board cover instead.
• Your current cover is scorched or shiny: A shiny patch means the surface has broken down and will stop gripping fabric. A scorched spot will not wash out. Replace the cover rather than pressing on a failing surface.
• You want a colour that hides marks: The cover comes in Ironing Cover Off White. A light surface shows scorching early, which is a warning rather than a flaw. Choose off white if you want visible feedback on iron temperature.

Product facts

• Cinderella Ironing Cover: The Cinderella Ironing Cover is a spare part designed for the Cinderella Table and is steam-ironing proof. Compatibility with the Cinderella Table is the deciding factor, and the steam-ironing proof surface suits anyone who presses with steam rather than dry heat.
• Cinderella Ironing Cover: It is available in Ironing Cover Off White, and colour is the option offered. A light surface makes it easier to see the fabric you are pressing and shows scorching early, so you can adjust your iron before the cover is damaged.
• Blond Small Bowl: The Blond Small Bowl is 30 cl and comes in White/Dot and White/Stripe pattern options. If you are refreshing a utility or laundry area at the same time, this is a small, stackable piece that suits holding pins, buttons, or clips without taking up ironing space.

Who the Cinderella Ironing Cover is for

Best for

• Owners of the Cinderella Table who need to replace a worn or scorched cover
• Anyone who irons with a steam iron and wants a steam-ironing proof surface
• Households that want an off white pressing surface where scorching shows early

Not for

• Standard ironing boards, which need a cover sized to the board's own length and width
• Buyers looking for a universal cover that fits any table or board
• Anyone hoping a new cover will fix damage to the table itself rather than the cover